Log the pump service and check the flow came back
A new impeller should bring the flow back. If it doesn’t, the problem is somewhere else, like the suction, a foot valve or the channel, and you only find out when a block falls behind.
The Pump and channel watcher logs the service against the river pump with its hours and parts, pulls the flow meter’s readings from before it and checks the first run after to see the flow came back.
- When · On demand
- “[mechanic] did the river pump today. New impeller and bearings, hour meter 3,140.”
- You get
- Service on the river pump’s record with hours and parts; flow before and after from the meter; a flag if it didn’t come back
- Approval level
- Act with approval. Prepares it fully. You tap yes. You can change it.
- Useful for
- Irrigated cropsOrchards and vinesDairy
What it reads
- Machinery services: river pump, last service at 520 hours
- Monitoring: river pump flow meter, start of season and the last fortnight
- Faults noted on the river pump this season
- The mechanic’s text or invoice
What you get
- The service logged on the river pump at 3,140 hours, with the parts
- Flow at the start of the season and just before the service, from the flow meter
- Flow on the first run after, with a flag if it’s not back
- The hours at the next service
When it stops and asks you
- The hour meter reading is lower than the last one logged
- The flow meter had gaps around the service
- Flow after the service is no better
How often
Each pump service, a few times a year
Who uses it
OwnersManagers
What it uses
SMS and voice notes
Text the team, send a voice note or a photo, or forward a message. There’s no new app to learn.
Nothing official leaves the farm without your yes.This job runs at Act with approval: prepares it fully. You tap yes. You can change that any time.
The conversation
How the job plays out, step by step.
Pump and channel watcher
Started 7:12am · On demand
- Start to done
- 3 min
- Agent actions
- 4
- Needed you
- 2×
[AGENT NAME]For the Pump and channel watcher[mechanic] did the river pump today. New impeller and bearings, hour meter 3,140.
You · 7:12am

Pump and channel watcher
Pulled the river pump’s service history and flow

Log the service on the river pump at 3,140 hours: new impeller and bearings, [mechanic], today? Before it, the flow meter had it down to 74 L/s from 92 at the start of the season. I’ll check it on the next run.
[AGENT NAME] · 7:12am
Yep, log it.
You · 7:14am

Pump and channel watcher
Logged the service

Pump and channel watcher
Checked the flow on the first run after the service

First run since the service: 90 L/s over 10 hours, near enough back to where it started the season. The impeller was the problem.
[AGENT NAME] · 7:14am
Done · 7:15am4 saved
- The service logged on the river pump at 3,140 hours, with the partsSaved
- Flow at the start of the season and just before the service, from the flow meterSaved
- Flow on the first run after, with a flag if it’s not backSaved
- The hours at the next serviceSaved
Behind the scenes
7:12am
You ask
“[mechanic] did the river pump today. New impeller and bearings, hour meter 3,140.”
7:12am+10 sec
Pump and channel watcher works on it · 2 steps
Pulled the river pump’s service history and flow
records.searchriver pump last serviced at 520 hours, [date]sensors.read_waterriver pump flow meter, 92 L/s at the start of the season, 74 L/s average over the last fortnight
7:12am+2 sec
[AGENT NAME] asks for your yes
“Log the service on the river pump at 3,140 hours: new impeller and bearings, [mechanic], today? Before it, the flow meter had it down to 74 L/s from 92 at the start of the season. I’ll check it on the next run.”
7:14am+3 min
You approve
“Yep, log it.”
7:14am+7 sec
Pump and channel watcher works on it · 1 step
Logged the service
records.log_serviceriver pump, 3,140 h, impeller and bearings, [mechanic], [date]
7:14am+7 sec
Pump and channel watcher works on it · 1 step
Checked the flow on the first run after the service
sensors.read_waterriver pump 90 L/s over a 10 hour run, [date]
7:14am+2 sec
[AGENT NAME] messages you
“First run since the service: 90 L/s over 10 hours, near enough back to where it started the season. The impeller was the problem.”
7:15am+3 sec
Pump and channel watcher Done
Service on the river pump’s record at 3,140 hours; flow back to 90 L/s on the meter; next service due at [hours]
memory.rememberRiver pump 90 L/s after the new impeller, [date]
An example with made-up data. Names and figures in [brackets] are placeholders.
The agent behind it
Pump and channel watcherIrrigation & waterThe Pump and channel watcher keeps the water moving: pump faults, power use, off-peak runs and channel checks.
What it won’t do
- Start, stop or change a pump
- Book a contractor without asking first
- Make up a reading
More jobs the Pump and channel watcher does.
- Flag a pump drawing more power than usualDaily
- Check the pumps ran off-peak this monthScheduled
- Book pump services by run hours before the seasonScheduled
- Log a channel leak and raise the repair jobOn demand
- Catch a pump running with no water movingDaily
- Walk the channels before the first watering of the seasonScheduled
The farm software this job works from
Put [AGENT NAME] to work on your farm.
We’re taking a small number of pilot farms in Australia. Start with one or two agents and add more as you go.
See it on a farm like yours.
30 minutes with Thomas, our founder, on records like your own.
Livestock, paddocks, visitors and tanks, in one place.
The farm management software comes with every plan. Keep the software you already use, or use ours.
Not ready yet? Start with a free calculator.
The sums you do every week, for stock, pasture, crops and the books. No sign-up.
Watch a job before you commit.
Pick a playbook and see it play out, step by step.


