Catch a pump still running when peak power starts
A timer knocked out by a power cut, or a set started late, runs straight into peak, and nobody knows until the bill comes a month later. By then it’s happened twenty times.
The Pump and channel watcher reads the flow meters on every pump at the start of peak, matches any still moving water to the watering job behind it, works out what the peak hours will cost and puts a timer fix on the list after your yes.
- When · Scheduled
- Each weekday at the start of your peak tariff window, [time]
- You get
- Pumps running into peak, with the job behind each; what the extra peak hours cost; a job to reset the timer
- Approval level
- Act with approval. Prepares it fully. You tap yes. You can change it.
- Useful for
- Irrigated cropsOrchards and vinesDairy
What it reads
- Monitoring: the flow meter on each pump, last 12 hours
- Job list: today’s watering jobs, with start times and hours
- Your tariff: peak and off-peak times and rates
- Each pump’s power rating
What you get
- Any pump still moving water at the start of peak
- The watering job behind it and when it’ll finish
- What the peak hours cost against running off-peak
- A job to reset the timer before tonight
When it stops and asks you
- A pump is running with no watering job behind it
- The block it’s on can’t wait until tonight
- A flow meter has no reading since this morning
How often
Every weekday in the irrigation season
Who uses it
ManagersFarm staff
What it uses
Water monitors and weather stations
Trough, tank and rain gauge readings would start jobs for the team.
SMS and voice notes
Text the team, send a voice note or a photo, or forward a message. There’s no new app to learn.
The last one makes it better, but it works without it.
Nothing official leaves the farm without your yes.This job runs at Act with approval: prepares it fully. You tap yes. You can change that any time.
The conversation
How the job plays out, step by step.
Pump and channel watcher
Started 6:00am · Scheduled
- Start to done
- 5 min
- Agent actions
- 4
- Needed you
- 2×
[AGENT NAME]For the Pump and channel watcherOn schedule · 6:00am
Start of peak power on a weekday

Pump and channel watcher
Read every pump’s flow meter and matched it to the day’s jobs

Pump 2 is still running into peak. Its flow meter shows it started at 11:40 this morning, not 10 pm last night like the Block 6 job had it. With 10 hours to run it goes till about 9:40 tonight, about 6 hours of it in peak. At your rates that’s about [amount] more than overnight. I can’t stop it from here. Did the timer get knocked out?
[AGENT NAME] · 6:00am
Power went off overnight. Block 6 is gasping, let it run. Timer needs resetting though.
You · 6:02am

I’ll put a job on [irrigator]’s list to reset Pump 2’s timer to the 10 pm start before tonight. OK?
[AGENT NAME] · 6:02am
Yep.
You · 6:05am

Pump and channel watcher
Added the job
Done · 6:05am4 saved
- Any pump still moving water at the start of peakSaved
- The watering job behind it and when it’ll finishSaved
- What the peak hours cost against running off-peakSaved
- A job to reset the timer before tonightSaved
Behind the scenes
6:00am
Trigger On schedule
Start of peak power on a weekday
- Schedule: weekdays at [time], the start of peak
6:00am+13 sec
Pump and channel watcher works on it · 3 steps
Read every pump’s flow meter and matched it to the day’s jobs
sensors.read_waterPump 2 at 68 L/s since 11:40 am, nothing overnight; river pump and Pump 3 stopped at 6 amrecords.searchjob, Water Block 6 for 10 hours from 10 pm last night, [irrigator]- Pump 2: 45 kW
6:00am+2 sec
[AGENT NAME] messages you
“Pump 2 is still running into peak. Its flow meter shows it started at 11:40 this morning, not 10 pm last night like the Block 6 job had it. With 10 hours to run it goes till about 9:40 tonight, about 6 hours of it in peak. At your rates that’s about [amount] more than overnight. I can’t stop it from here. Did the timer get knocked out?”
6:02am+3 min
You reply
“Power went off overnight. Block 6 is gasping, let it run. Timer needs resetting though.”
6:02am+2 sec
[AGENT NAME] asks for your yes
“I’ll put a job on [irrigator]’s list to reset Pump 2’s timer to the 10 pm start before tonight. OK?”
6:05am+3 min
You approve
“Yep.”
6:05am+7 sec
Pump and channel watcher works on it · 1 step
Added the job
jobs.createReset Pump 2 timer to a 10 pm start, today, [irrigator]
6:05am+3 sec
Pump and channel watcher Done
Pump 2’s run into peak noted with what it cost; the timer reset on [irrigator]’s list for today; every pump checked again at tomorrow’s peak start
reports.draftPump 2 ran about 6 hours into peak, [date], after a power cut
An example with made-up data. Names and figures in [brackets] are placeholders.
The agent behind it
Pump and channel watcherIrrigation & waterThe Pump and channel watcher keeps the water moving: pump faults, power use, off-peak runs and channel checks.
What it won’t do
- Start, stop or change a pump
- Book a contractor without asking first
- Make up a reading
More jobs the Pump and channel watcher does.
- Flag a pump drawing more power than usualDaily
- Check the pumps ran off-peak this monthScheduled
- Book pump services by run hours before the seasonScheduled
- Log a channel leak and raise the repair jobOn demand
- Catch a pump running with no water movingDaily
- Walk the channels before the first watering of the seasonScheduled
The farm software this job works from
Put [AGENT NAME] to work on your farm.
We’re taking a small number of pilot farms in [REGION]. Start with one or two agents and add more as you go.
See it on a farm like yours.
30 minutes with Thomas, our founder, on records like your own.
Livestock, paddocks, visitors and tanks, in one place.
The farm management software comes with every plan. Keep the software you already use, or use ours.
Not ready yet? Start with a free calculator.
The sums you do every week, for stock, pasture, crops and the books. No sign-up.
Watch a job before you commit.
Pick a playbook and see it play out, step by step.


